В сравнении 0
Войти  /  Регистрация

SNAP-PAC-S1

(0)
SNAP-PAC-S1
86 211 руб
- + шт
Спецификации:

Processor

266 MHz 32-bit ColdFire® 5475 with integrated floating-point unit (FPU)

Memory

SNAP-PAC-S1 and SNAP-PAC-S2

  Total RAM: 32 MB

  Total RAM for PAC Control Strategies: 16 MB

  Battery-backed RAM: 8 MB

  RAM File Storage: 2.5 MB

  Flash File Storage: 4 MB

 

SNAP-PAC-S1-W and SNAP-PAC-S2-W

  Total RAM: 128 MB

  Total RAM for PAC Control Strategies: 64MB

  Battery-backed RAM: 8 MB

  RAM File Storage: 16 MB

  Flash File Storage: 4 MB

Removable storage

(Models with manufacture dates of June 2014 and newer. Requires firmware R9.4a or higher and loader R6.1a or higher) MicroSD card slot: supports microSD or microSDHC cards to 32 GB. 

(Models with manufacture dates of November 2008 through May 2014 with firmware R8.4 or higher) McroSD card slot: supports microSD cards up to 2 GB.

Backup battery

SNAP-PAC-S1s with serial number 625654 or higher and all SNAP-PAC-S2s: Rechargeable (recharges whenever the brain has power), 1-year power-off data retention (replacement part number: SNAP-PAC-BATTERY-ML2430)

SNAP-PAC-S1s with serial number 625653 or lower: User-replaceable 3.6-volt TL 5242 /W lithium, 10-year minimum power-off data retention (replacement part number: G4BATT32)

Ethernet Communication (wired) to host and I/O

Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connec­tors). Each interface has a separate IP address (separate subnet).

Ethernet Communication (wireless)*

Wireless LAN interface with separate IP address. 

Topologies: Infrastructure, Ad-Hoc 

Security: 802.11i; AES - Compatible with WPA2 Personal, TKIP - Compatible with WPA Personal, WEP. Note: TKIP/AES security is not supported in Ad-Hoc mode.

Frequency 802.11a: 5.180–5.240 GHz, 5.745–5.825 GHz

Frequency 802.11b/g: 2.412–2.472 GHz, 2.484 GHz

Transmit Power: 15 dBm maximum

Antenna Connector: Reverse polarity SMA (RP-SMA or RSMA)

Roaming: Supported within an SSID (Service Set Identifier) only

Serial Communication

SNAP-PAC-S1

RS-232 serial: Two RS-232 serial ports (one DB-9 and one pluggable connec­tor); one port has full handshaking. PPP is supported only on port 0. Buffer size: 512 bytes each for RX and TX.

RS-485 serial: One RS-485 serial port (pluggable connector); two-wire RS-485; optionalmistic signal interrupts. Range (serial multidrop): 32 stations maximum on a segment (including PC, controller, and I/O units); up to 3000 ft (914 m) on a segment. Buffer size: 512 bytes each for RX and TX.

 

SNAP-PAC-S2

Four serial ports that can be used as general purpose ports or for serial I/O units; each port is software configurable as either RS-232 (Tx, Rx, COM, DTR, DCD, RTS, CTS) or as RS-485 (2-wire, 4-wire, optional termination, optional biasing); optional mistic signal interrupts. Buffer size: 512 bytes each for RX and TX.

Power requirements

8–32 VDC ±0.5, 11.3 VA maximum

(SNAP-PAC-S1 controllers with serial numbers below 500,000 use 8–24 VDC)

Operating temperature

-20 °C to 60 °C

Storage temperature

-40 °C to 85 °C

Humidity

0% to 95% relative humidity, non-condensing

Software

Includes programming, HMI software, and configuration software; included with purchase of controller.

PAC Project Basic

PAC Project Basic plus OPC 2.0-compliant OPC server, OptoControl strategy and OptoDisplay project importing, support for serial mistic I/O units, and Ethernet link redundancy support.

 

Use HTTPS to access data (read/write or read-only) from controller tags using your chosen programming language. Data returned in JSON. More information atdeveloper.opto22.com

 PAC Project Professional

 

 

 

 

 

 REST API

 

Number of charts that can run simultaneously

32

Other features

Multiple protocol support including TCP/IP, FTP, SNMP v2.0c (with firmware 8.2a), Modbus/TCP, EtherNet/IP™, and OptoMMP™.

Real-time clock

FTP server/client with file system (in RAM and in removable storage)

Ethernet link redundancy or network segmenting

Agency certifications

(-W models only) U.S., FCC Part 15 Subpart C; Canada, IC RSS-210

(-FM models only) Factory Mutual approved

All models except -W models: CE, RoHS, DFARS

-W models: DFARS

Warranty

30 months from date of manufacture

* Requires a Wired+Wireless model (SNAP-PAC-S1-W or SNAP-PAC-S2-W)

Документация:
0959_SNAP_PSDIN_Install_Note / 1465_OptoMMP_Protocol_Guide / 1569_SNAP_PAC_System_Product_Guide / 1584_SNAP_PAC_S-Series_data_sheet / 1592_SNAP_PAC_S_series_Users_Guide / 1634_PAC_White_Paper / 1646_Tech_Note_SNAP_PAC_Memory / 1677_SNAP_PAC_Controller_Brain_Comparison_Chart / 1678_Modbus_TCP_Protocol_Guide / 1679_SNAP-PAC-S1 In-the-Box_Voltage_Notice_4up / 1693_Current_and_Legacy_SNAP_Product_Charts / 1696_SNAP_PAC_System_Specification_Guide / 1704_PAC_Manager_Users_Guide / 1714_PAC_Manager_Users_Guide_Legacy_Edition / 1724_Six_Reasons_SNAP_PAC_System / 1729_Case_Study_Ballarat_Health_Services / 1733_Considerations_for_Choosing_a_PAC / 1736_Software_for_Programmable_Automation_Controllers / 1747_Ethernet_IP_Implementation_Tech_Note / 1770_Ethernet_IP_for_SNAP_PAC_Protocol_Guide / 1789_Updating_Loader_on_SNAP_Device_Technical_Note / 1796_Networking_Opto22_Products / 1820_Communication_Tools_Protocols_for_Opto_22_Products / 1826_Quick_Guide_to_SNAP_PAC_System_Troubleshooting / 1909_IO4AB_Users_Guide / 2011_Using_Modbus_Devices_with_Opto_22_Products_Tech_Note / 2018_Using_microSD_w_Older_Controller_Firmware_Tech_Note / 2037_SNAP_PAC_Controller_Comparison_Chart / 2137_Application_Brief_SCADA_Solutions / 2149_Press_Release_dotNET_Controller_SDK / 2173_Your_IoT_Primer_white_paper / 2184_Edge_Computing_Primer / 2186_SNAP_PAC_REST_API_IT_Technical_Note / 2187_SNAP_PAC_REST_API_OT_Technical_Note / 2189_Press_Release_REST_API_in_SNAP_PAC / 2191_Press_Release_Node_RED_Nodes_for_SNAP_PACs / 2193_Case_Study_Toyo_Tanso / 2198_Connect_Industrial_Devices_to_IBM_Watson_IoT_Tech_Note / 2211_Case_Study_ISI_Water / 2215_State_of_the_IIoT_2017_white_paper / 2216_Connect_Real-world_Data_to_an_AT&T_M2X_Device_Technical_Note / 2217_Press_Release_IBM_Watson_IoT_Partner / 2218_Application_Brief_Perceptive_Controls
Загрузки:
Controller Time Synchronization Application / OptoTagPreserve / CAD Drawing: SNAP-PAC-S1 and SNAP-PAC-S1-FM Standalone Industrial Controller / Firmware for all SNAP PAC products / SNAP-PAC-S1 Controller Firmware / SNAP PAC S-Series Controller Bootloader / Allen-Bradley DF1 Integration Kit for ioControl
Загрузить:
Загрузить / Загрузить / Загрузить / Загрузить / Загрузить / Загрузить
Аксессуары:
E1 / E2

Программируемый контроллер автоматизации SNAP-PAC-S1 обеспечивает мощные алгоритмы управления и обмен данными в системах промышленной автоматизации, мониторинга и сбора данных.

SNAP-PAC-S1 полностью интегрирован с пакетом программ PAC Project, управляющими модулями SNAP-PAC и модулями ввода-вывода. Система SNAP PAC позволяет создавать локальные и распределенные системы управления с использованием цифровых, аналоговых и интерфейсных модулей, настраивать контуры PID регулирования и интегрировать автоматику в общую систему управления предприятием.  

Программирование

SNAP-PAC-S1 программируется с помощью встроенного программного обеспечения PAC Control. PAC Control является сервисной программой (на основе блок-схем) для разработки управляющих приложений или стратегий. Вы создаете и отлаживаете стратегию на вашем компьютере и затем загружаете ее на PAC, где она самостоятельно запускается.

REST API:

Все точки ввода / вывода и переменные из стратегии доступны для безопасного доступа с помощью встроенного HTTPS сервера и RESTful API (данные поставляются в формате JSON). 

Для получения полной документации и API шагов см. developer.opto22.com. Кроме того предоставляются два узла NODE-RED.

Обратите внимание, что для использования REST API минимально необходимо иметь прошивку для контроллера R9.5a и PAC Project R9.5a.

HMIs

Вы можете создавать полнофункциональные пользовательские (человеко-машинные) интерфейсы, используя программное обеспечение PAC Display с той же самой базой тэгов, которую вы уже разработали в PAC Control. Или воспользоваться OPTO22 GROOV, чтобы построить и просматривать HTMs, которые можно использовать практически на любом компьютере, планшете или смартфоне любого размера экрана, от любого производителя, используя только современный веб-браузер (например, Firefox или Chrome). Узнайте больше на groov.com. 

Работа в сети.

В каждый SNAP-PAC-S1 включены два независимых сетевых интерфейса Ethernet. Эти интерфейсы имеют разные IP-адреса и могут использоваться для отделения управляющей сети от сети компании или для обеспечения резервирования канала Ethernet в случае сбоя в работе или планового ремонта. Кроме того, можно создать систему с резервированием контроллеров с использованием двух идентичных контроллеров S-серии, SNAP PAC Redundancy Option Kit, и PAC Project Professional 9.0.

Последовательная связь

SNAP-PAC-S1 также имеет три последовательных порта: порт RS-232 с полным аппаратным квитированием, идеально подходит для связи PPP с использованием модема; другой порт RS-232 для подключения непосредственно к последовательным устройствам; и порт RS-485 для подключения к SNAP PAC Serial brains или к модулям ввода / вывода с протоколом mistic.

Если вам нужна версия, сертифицированная ассоциацией производителей, см. SNAP-PAC-S1-FM.

Если вам нужен подобный PAC, который также обменивается данными по беспроводной сети, см SNAP-PAC-S1-W.

Для получения более подробной информации см вкладку Характеристики.

Для сравнения возможностей контроллера см. SNAP PAC Controller and Brain Comparison Chart.

Спецификации

Processor

266 MHz 32-bit ColdFire® 5475 with integrated floating-point unit (FPU)

Memory

SNAP-PAC-S1 and SNAP-PAC-S2

  Total RAM: 32 MB

  Total RAM for PAC Control Strategies: 16 MB

  Battery-backed RAM: 8 MB

  RAM File Storage: 2.5 MB

  Flash File Storage: 4 MB

 

SNAP-PAC-S1-W and SNAP-PAC-S2-W

  Total RAM: 128 MB

  Total RAM for PAC Control Strategies: 64MB

  Battery-backed RAM: 8 MB

  RAM File Storage: 16 MB

  Flash File Storage: 4 MB

Removable storage

(Models with manufacture dates of June 2014 and newer. Requires firmware R9.4a or higher and loader R6.1a or higher) MicroSD card slot: supports microSD or microSDHC cards to 32 GB. 

(Models with manufacture dates of November 2008 through May 2014 with firmware R8.4 or higher) McroSD card slot: supports microSD cards up to 2 GB.

Backup battery

SNAP-PAC-S1s with serial number 625654 or higher and all SNAP-PAC-S2s: Rechargeable (recharges whenever the brain has power), 1-year power-off data retention (replacement part number: SNAP-PAC-BATTERY-ML2430)

SNAP-PAC-S1s with serial number 625653 or lower: User-replaceable 3.6-volt TL 5242 /W lithium, 10-year minimum power-off data retention (replacement part number: G4BATT32)

Ethernet Communication (wired) to host and I/O

Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connec­tors). Each interface has a separate IP address (separate subnet).

Ethernet Communication (wireless)*

Wireless LAN interface with separate IP address. 

Topologies: Infrastructure, Ad-Hoc 

Security: 802.11i; AES - Compatible with WPA2 Personal, TKIP - Compatible with WPA Personal, WEP. Note: TKIP/AES security is not supported in Ad-Hoc mode.

Frequency 802.11a: 5.180–5.240 GHz, 5.745–5.825 GHz

Frequency 802.11b/g: 2.412–2.472 GHz, 2.484 GHz

Transmit Power: 15 dBm maximum

Antenna Connector: Reverse polarity SMA (RP-SMA or RSMA)

Roaming: Supported within an SSID (Service Set Identifier) only

Serial Communication

SNAP-PAC-S1

RS-232 serial: Two RS-232 serial ports (one DB-9 and one pluggable connec­tor); one port has full handshaking. PPP is supported only on port 0. Buffer size: 512 bytes each for RX and TX.

RS-485 serial: One RS-485 serial port (pluggable connector); two-wire RS-485; optionalmistic signal interrupts. Range (serial multidrop): 32 stations maximum on a segment (including PC, controller, and I/O units); up to 3000 ft (914 m) on a segment. Buffer size: 512 bytes each for RX and TX.

 

SNAP-PAC-S2

Four serial ports that can be used as general purpose ports or for serial I/O units; each port is software configurable as either RS-232 (Tx, Rx, COM, DTR, DCD, RTS, CTS) or as RS-485 (2-wire, 4-wire, optional termination, optional biasing); optional mistic signal interrupts. Buffer size: 512 bytes each for RX and TX.

Power requirements

8–32 VDC ±0.5, 11.3 VA maximum

(SNAP-PAC-S1 controllers with serial numbers below 500,000 use 8–24 VDC)

Operating temperature

-20 °C to 60 °C

Storage temperature

-40 °C to 85 °C

Humidity

0% to 95% relative humidity, non-condensing

Software

Includes programming, HMI software, and configuration software; included with purchase of controller.

PAC Project Basic

PAC Project Basic plus OPC 2.0-compliant OPC server, OptoControl strategy and OptoDisplay project importing, support for serial mistic I/O units, and Ethernet link redundancy support.

 

Use HTTPS to access data (read/write or read-only) from controller tags using your chosen programming language. Data returned in JSON. More information atdeveloper.opto22.com

 PAC Project Professional

 

 

 

 

 

 REST API

 

Number of charts that can run simultaneously

32

Other features

Multiple protocol support including TCP/IP, FTP, SNMP v2.0c (with firmware 8.2a), Modbus/TCP, EtherNet/IP™, and OptoMMP™.

Real-time clock

FTP server/client with file system (in RAM and in removable storage)

Ethernet link redundancy or network segmenting

Agency certifications

(-W models only) U.S., FCC Part 15 Subpart C; Canada, IC RSS-210

(-FM models only) Factory Mutual approved

All models except -W models: CE, RoHS, DFARS

-W models: DFARS

Warranty

30 months from date of manufacture

* Requires a Wired+Wireless model (SNAP-PAC-S1-W or SNAP-PAC-S2-W)

Загрузить
Загрузить / Загрузить / Загрузить / Загрузить / Загрузить / Загрузить
Аксессуары
E1 / E2

Наличие на складах

0959_SNAP_PSDIN_Install_Note Detail
1465_OptoMMP_Protocol_Guide Detail
1569_SNAP_PAC_System_Product_Guide Detail
1584_SNAP_PAC_S-Series_data_sheet Detail
1592_SNAP_PAC_S_series_Users_Guide Detail
1634_PAC_White_Paper Detail
1646_Tech_Note_SNAP_PAC_Memory Detail
1677_SNAP_PAC_Controller_Brain_Comparison_Chart Detail
1678_Modbus_TCP_Protocol_Guide Detail
1679_SNAP-PAC-S1 In-the-Box_Voltage_Notice_4up
1693_Current_and_Legacy_SNAP_Product_Charts Detail
1696_SNAP_PAC_System_Specification_Guide Detail
1704_PAC_Manager_Users_Guide Detail
1714_PAC_Manager_Users_Guide_Legacy_Edition Detail
1724_Six_Reasons_SNAP_PAC_System Detail
1729_Case_Study_Ballarat_Health_Services Detail
1733_Considerations_for_Choosing_a_PAC Detail
1736_Software_for_Programmable_Automation_Controllers Detail
1747_Ethernet_IP_Implementation_Tech_Note Detail
1770_Ethernet_IP_for_SNAP_PAC_Protocol_Guide Detail
1789_Updating_Loader_on_SNAP_Device_Technical_Note Detail
1796_Networking_Opto22_Products Detail
1820_Communication_Tools_Protocols_for_Opto_22_Products Detail
1826_Quick_Guide_to_SNAP_PAC_System_Troubleshooting Detail
1909_IO4AB_Users_Guide Detail
2011_Using_Modbus_Devices_with_Opto_22_Products_Tech_Note Detail
2018_Using_microSD_w_Older_Controller_Firmware_Tech_Note Detail
2037_SNAP_PAC_Controller_Comparison_Chart Detail
2137_Application_Brief_SCADA_Solutions Detail
2149_Press_Release_dotNET_Controller_SDK Detail
2173_Your_IoT_Primer_white_paper Detail
2184_Edge_Computing_Primer Detail
2186_SNAP_PAC_REST_API_IT_Technical_Note Detail
2187_SNAP_PAC_REST_API_OT_Technical_Note Detail
2189_Press_Release_REST_API_in_SNAP_PAC Detail
2191_Press_Release_Node_RED_Nodes_for_SNAP_PACs Detail
2193_Case_Study_Toyo_Tanso Detail
2198_Connect_Industrial_Devices_to_IBM_Watson_IoT_Tech_Note Detail
2211_Case_Study_ISI_Water Detail
2215_State_of_the_IIoT_2017_white_paper Detail
2216_Connect_Real-world_Data_to_an_AT&T_M2X_Device_Technical_Note Detail
2217_Press_Release_IBM_Watson_IoT_Partner Detail
2218_Application_Brief_Perceptive_Controls Detail
Controller Time Synchronization Application Detail
OptoTagPreserve Detail
CAD Drawing: SNAP-PAC-S1 and SNAP-PAC-S1-FM Standalone Industrial Controller Detail
Firmware for all SNAP PAC products Detail
SNAP-PAC-S1 Controller Firmware Detail
SNAP PAC S-Series Controller Bootloader Detail
Allen-Bradley DF1 Integration Kit for ioControl Detail
E1 Некое описание аксессуара 1.
E2 Некое описание аксессуара 2.